We don't want to have heterogeous ceph.conf anymore and believe that we
should have the right section for the running daemon.
If we don't do this and use profiles, e.g: rgw, we will get a new rgw
section on some of the nodes.
Signed-off-by: Sébastien Han <seb@redhat.com>
Remove `rgw enable static website` and `rgw enable usage log` from
ceph.conf and make it usable with ceph_config_overrides as profiles.
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
This commit introduces a new directory called "profiles" which
contains some set of variables for a particular use case. These profiles
provide guidance for certain scenarios such as:
* configuring rgw with keystone v3
Signed-off-by: Sébastien Han <seb@redhat.com>
The ceph.conf template needs to look for the value of monitor_interface
in hostvars[host] because there might be different values set per host.
Signed-off-by: Andrew Schoen <aschoen@redhat.com>
remove `ceph_mon_docker_interface` and use `monitor_interface` instead
for both containerized and non-containerized deployment.
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
e8187f6 does not fix the ipv6 as expected since `ansible_default_*` are
filled with the IP address carried by the network interface used by the
default gateway route. By the way, it assumes that the MON_IP address will
be this IP address which is not always the case.
We need to keep using the previous fact but add some intelligence in the
template to determine how to retrieve the ipv4|ipv6 address since the path
to the fact in `hostvars` is not the same according to ipv4 vs ipv6 case.
Fix: 1569
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
Remove "osd mkfs type" and the other pre-Bluestore parameters from the
generated ceph.conf so that disk activation on OSDs will work. The
current default xfs config results in a failed deployment and
incorrect partition metadata.
`ceph-docker-common`:
At the moment there is a lot of duplicated tasks in each
`./roles/ceph-<role>/tasks/docker/main.yml` that could be refactored in
`./roles/ceph-docker-common/tasks/main.yml`.
`*_containerized_deployment` variables:
All `*_containerized_deployment` have been refactored to a single
variable `containerized_deployment`
duplicate `cephx` variables in `group_vars/* have been removed.
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
"rgw override bucket index max shards" and
"rgw bucket default quota max objects" were in the
client section of the ceph.conf and not being
applied, this commit moves them to global
Resolves: bz#1391500
Signed-off-by: Ali Maredia <amaredia@redhat.com>
Change civetweb_num_thread default to 100
Add capability to override number of pgs for
rgw pools.
Add ceph.conf vars to enable default bucket
object quota at users choosing into the ceph.conf.j2
template
Resolves: rhbz#1437173
Resolves: rhbz#1391500
Signed-off-by: Ali Maredia <amaredia@redhat.com>
This allows the user to set ip_version to either ipv4 or ipv6. This
resolves a bug where monitor_address is set to an ipv6 address, but the
template fails to render because it's hardcoded to look for an 'ipv4'
key in the ansible facts.
See: https://bugzilla.redhat.com/show_bug.cgi?id=1416010
Signed-off-by: Andrew Schoen <aschoen@redhat.com>
Resolves: bz#1416010
Allow for more operator flexibility in the `rgw frontends` setting
while maintaining backwards compatibility with the old vars. This
allows an operator to, for example, use the civetweb settings for
implementing SSL ports.
For available civetweb configuration parameters, see:
https://github.com/civetweb/civetweb/blob/master/docs/UserManual.md
The Keystone v2 APIs are deprecated and scheduled to be removed in
Q release of Openstack. This adds support for configuring RGW to
use the current Keystone v3 API.
The PKI keys are used to decrypt the Keystone revocation list when
PKI tokens are used. When UUID or Fernet token providers are used in
Keystone, PKI certs may not exist, so we now accommodate this scenario
by allowing the operator to disable the PKI tasks.
Jewel added support for user/pass authentication with Keystone,
allowing deployers to disable Keystone admin token as required
for production deployments.
This implements configuration for the new RGW Keystone user/pass
authentication feature added in Jewel.
See docs here: http://docs.ceph.com/docs/master/radosgw/keystone/
Before this patch only the address for the first mon would show
in the ceph.conf even if there were multiple mons in the inventory.
Signed-off-by: Andrew Schoen <aschoen@redhat.com>
libfcgi is dead upstream (http://tracker.ceph.com/issues/16784)
The RGW developers intend to remove libfcgi support entirely before the
Luminous release.
Since libfcgi gets little-to-no developer attention or testing, remove
it entirely from ceph-ansible.
Before this commit if you had set monitor_interface in your
inventory file for a specific host it would be ignored and the value
in group_vars/all would have been used.
Also, this enables support for monitor_address again as it had been
broken by previous changes to this template.
Signed-off-by: Andrew Schoen <aschoen@redhat.com>
For some providers (such as upcoming Linode support), some NICs may have
multiple IP addresses. (In the case of Linode, the only NIC has a public
and private IP address.) This is normally okay as we can use the
ceph.conf cluster_network and public_network variables to force the
monitor to listen on the addresses we want. However, we also need
ansible to set the correct monitor IP addresses in "mon hosts" (i.e. the
addresses the monitors will listen on!). This new monitor_address_block
setting tells ansible which IP address to use for each monitor.
Signed-off-by: Patrick Donnelly <pdonnell@redhat.com>
- Gather facts only for mons before processing ceph-mon role serially in
containerized playbook sample
- Updated ceph.conf in order to generate a valid ceph.conf
Signed-off-by: Ivan Font <ivan.font@redhat.com>
Prior to this change, each ceph cluster node would end up with several
"qemu-client-$pid.log" files owned by root. The [client] section would
capture *all* client activity (for example the "ceph health" command,
etc), not just librbd-in-qemu.
Restrict this section to libvirt clients only so that we don't generate
these spurious log files for other Ceph client traffic.
Signed-off-by: Ken Dreyer <kdreyer@redhat.com>
Since ##461 we have been having the ability to override ceph default
options. Previously we had to add a new line in the template and then
another variable as well. Doing a PR for one option was such a pain. As
a result, we now have tons of options that we need to maintain across
all the ceph version, yet another painful thing to do.
This commit removes all the ceph options so they are handled by ceph
directly. If you want to add a new option, feel free to to use the
`ceph_conf_overrides` variable of your `group_vars/all`.
Risks, for those who have been managing their ceph using ceph-ansible
this is not a trivial change as it will trigger a change in your
`ceph.conf` and then restart all your ceph services. Moreover if you did
some specific tweaks as well, prior to run ansible you should update the
`ceph_conf_overrides` variable to reflect your previous changes.
To avoid service restart, you need to know a bit of ansible for this,
but generally the idea would be to run ansible on a dummy host to
generate the ceph.conf, then scp this file to all your ceph hosts and
you should be good.
Closes: #693
Signed-off-by: Sébastien Han <seb@redhat.com>
Introducing a new config option: `radosgw_civetweb_bind_ip` which points
to the `ansible_default_ipv4` by default. You can override this
variable. Use ansible facts to put a proper value.
Signed-off-by: Sébastien Han <seb@redhat.com>
This fixes the ceph.conf template so that it will look for an inventory
defined value for monitor_interface or for monitor_interface defined in
a group_vars file.
Signed-off-by: Andrew Schoen <aschoen@redhat.com>
This fixes a bug where monitor_interface might be set in your inventory
file and not by using group_vars or --extra-vars causing the template to
use the default address of 0.0.0.0 instead of the defined
monitor_interface.
Signed-off-by: Andrew Schoen <aschoen@redhat.com>
we now have the ability to enable the `cluster` variable with a specific
value that will determine the name of the cluster.
Signed-off-by: Sébastien Han <seb@redhat.com>
ceph.conf.j2 template requires a new line between mon_containerized_deployment_with_kv and fsid variables
With this commit , i have added a new line for better readablity
Sébastien Han
Guillaume Abrioux
Andrew Schoen
Peter Jenkins
Ali Maredia
Logan V
Jirayut Nimsaeng
Shengjing Zhu
Ken Dreyer
Gunwoo Gim (a.k.a. Nicho1as)
Proskurin Kirill
Patrick Donnelly
Ivan Font
Christoph Dwertmann
Huamin Chen
ksingh7
pprokop