When using monitor_address_block to determine the ip address of the
monitor node, we need an ip address available in that cidr to be
present in the ansible facts (ansible_all_ipv[46]_addresses).
Currently we don't check if there's an ip address available during
the ceph-validate role.
As a result, the ceph-config role fails due to an empty list during
ceph.conf template creation but the error isn't explicit.
TASK [ceph-config : generate ceph.conf configuration file] *****
fatal: [0]: FAILED! => {"msg": "No first item, sequence was empty."}
With this patch we will fail before the ceph deployment with an
explicit failure message.
Resolves: rhbz#1673687
Signed-off-by: Dimitri Savineau <dsavinea@redhat.com>
(cherry picked from commit 5c39735be5)
Tuned name of a task and error message to make it more user understandable
Fixes BZ 1648168 - ceph-validate : devices are not validated in non-collocated and lvm_batch scenario
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=1648168
Signed-off-by: VasishtaShastry <vipin.indiasmg@gmail.com>
(cherry picked from commit 34c25ef49b)
- updated README-MULTISITE
- re-added destroy.yml
- added tasks in ceph-validate to make sure the
rgw multisite vars are set
Signed-off-by: Ali Maredia <amaredia@redhat.com>
These checks will never pass unless ceph_stable_release is passed and
ceph-defaults is run before ceph-validate. Additionally, we don't want
to support deploying jewel upstream at ceph-ansible master.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1637537
Signed-off-by: Andrew Schoen <aschoen@redhat.com>
Allow user to choose between timesyncd, chronyd and ntpd
Installation will default to timesyncd since it is distributed as
part of the systemd installation for most distros.
Added note indicating NTP daemon type is not used for containerized
deployments.
Fixes issue #3086 on Github
Signed-off-by: Benjamin Cherian <benjamin_cherian@amat.com>
The linux kernel target layer, LIO, does not support the iscsi target to
mix ACLs that have chap enabled and disabled under the same tpg. This
patch adds a check and fails if this type of setup is detected.
This fixes Red Hat BZ:
https://bugzilla.redhat.com/show_bug.cgi?id=1615088
Signed-off-by: Mike Christie <mchristi@redhat.com>
fqdn configuration possibility caused a lot of trouble, it's adding a
lot of complexity because of multiple cases and the relation between
ceph-ansible and ceph-container. Moreover, there is no benefit for such
a feature.
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=1613155
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
This adds the action 'batch' to the ceph-volume module so that we can
run the new 'ceph-volume lvm batch' subcommand. A functional test is
also included.
If devices is defind and osd_scenario is lvm then the 'ceph-volume lvm
batch' command will be used to create the OSDs.
Signed-off-by: Andrew Schoen <aschoen@redhat.com>
Check if the interface provided:
* exists in the gathered facts (thus on the system)
* is active
* has an IP address (depending on ip_version )
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=1600227
Signed-off-by: Sébastien Han <seb@redhat.com>
Do not run device validation on every hosts, only on OSD nodes.
Signed-off-by: Sébastien Han <seb@redhat.com>
Co-authored-by: Guillaume Abrioux <gabrioux@redhat.com>
We know make sure that:
* devices are actually block special files
* length of dedicated_device is identical to devices
Signed-off-by: Sébastien Han <seb@redhat.com>
When playing ceph-mds role, mon nodes have set a fact with the default
pg num for osd pools, we can simply default to this value for cephfs
pools (`cephfs_pools` variable).
At the moment the variable definition for `cephfs_pools` looks like:
```
cephfs_pools:
- { name: "{{ cephfs_data }}", pgs: "" }
- { name: "{{ cephfs_metadata }}", pgs: "" }
```
and we have a task in `ceph-validate` to ensure `pgs` has been set to a
valid value.
We could simply avoid this check by setting the default value of `pgs`
to `hostvars[groups[mon_group_name][0]]['osd_pool_default_pg_num']` and
let to users the possibility to override this value.
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=1581164
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
A dev or rhcs install does not require ceph_stable_release to be set and
instead generates that by looking at the installed ceph-version.
However, at this point in the playbook ceph may not have been installed
yet and ceph-common has not be run.
Fixes: https://github.com/ceph/ceph-ansible/issues/2618
Signed-off-by: Andrew Schoen <aschoen@redhat.com>
Dimitri Savineau
VasishtaShastry
Guillaume Abrioux
Ali Maredia
Andrew Schoen
Benjamin Cherian
Mike Christie
Rishabh Dave
Sébastien Han