During the initial play, the docker command doesn't not exist and then
there is no stdout_lines to the command. So get allows us to fix this by
declaring an array if the command fails.
Signed-off-by: Sébastien Han <seb@redhat.com>
Use an intermediate variable to build the final `dedicated_devices` list
to avoid duplicate entry in that array. (We need a 1:1 relation between
`dedicated_devices` and `devices` since we are using a `with_together`
later.
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
With jewel, `bootstrap_rbd_keyring` is not set because of this condition:
```
when:
- ceph_release_num.{{ ceph_release }} >= ceph_release_num.luminous
```
Therefore, the task `try to fetch ceph config and keys` will fail.
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
* Change version from 2 to 3.
* use ceph_rhcs_cdn_debian_repo_version to use other repositories along
* with ceph_rhcs_cdn_debian_repo
Signed-off-by: Sébastien Han <seb@redhat.com>
Set volume_cache to unsafe for CI VMs.
We might be using tmpfs for volume disks soon, therefore 'unsafe' is a
prerequisite for volume_cache
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
Shared folder is not required for tests.
We should avoid hitting the error :
```
uninitialized constant VagrantPlugins::ProviderLibvirt::Action::ShareFolders
```
Also, disabling it might reduce the needed time in certains cases for the VMs
to be started.
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
If two environments are using the same subnet, we will get trouble
because of ips addresses conflicts.
This commit ensures each scenario has a uniq subnet for both public and cluster
network so we can setup several test environment at a time on a same hypervisor.
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
`ceph_release` isn't available at this step of the playbook because it
is set later based on the installed binaries.
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=1486062
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
The value of doing this is fairly low compare to the added value.
So we remove these tasks, if rbd pool on Jewel doesn't have the right PG
value you can always increase it.
Signed-off-by: Sébastien Han <seb@redhat.com>
the path `/dev/disk/by-path/pci-0000:00:01.1-ata-1.0` doesn't exist.
it has to be changed to `/dev/disk/by-path/pci-0000:00:01.1-ata-1`
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
All keyring are getting copied to all nodes.
This commit fixes a leftover from a previous code refactor.
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=1498583
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
iscsi-gw needs a 'rbd' pool to configure iscsi target.
Note: I could have used the facts already set in `ceph-mon` but I voluntarily
didn't do it to not create a dependancy between these two roles.
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
This commit refacts the code regarding all `set_osd_pool_default_*`
related tasks by avoiding usage of useless `set_fact` to determine
whether a key is present in `ceph_conf_overrides`.
Signed-off-by: Guillaume Abrioux <gabrioux@redhat.com>
The rbd pool is the default pool that gets created during ceph cluster
initializaiton. If we act on the rbd related operations too early, the
rbd pool does not exist yet. Move the call to perform rbd operations
to a later stage after other pools have been created.
The rbd_pool.yml playbook has all the operations related to the rbd pool.
Replace the always_run (deprecated) directive with check_mode.
Most of the ceph related tasks only need to run once. The run_once directive
executes the task on the first host.
The ceph sub-command to delete a pool is delete (not rm).
The changes submitted here were tested with this ceph version.
ceph version 0.94.9-9.el7cp (b83334e01379f267fb2f9ce729d74a0a8fa1e92c)
This upload includes these changes:
- Use the fail module (instead of assert).
- From luminous release, the rbd pool is no longer created by default.
Delete the code to create the rbd pool for luminous release
- Conform the .yml files to use the suggested syntax.
The commands are executed on the mcp nodes and I think shell ansible module
is the right one to use. The command module is used to execute commands on
remote nodes. I can make the change to use command module if that is
prefrerred.
Sébastien Han
Guillaume Abrioux
Michel Rode
Jan Provaznik
Al Lau